|
|
| | |
|
Making your own pre-bonded tips for the Cold link/loc/ring System OR the Hot Fusion Bonding System
|
|
Supplies you will need:
Bulk Hair
or
Weft Hair
or
Previously pre-bonded hair you want to re-bond
Heating element to melt bond:
Hot Pot
or
Fusion iron
or
glue gun
Bond for the ends of the tip:
Fusion chips
or
pellets
or
glue sticks
Small shears to trim tip of I tip
Drawing mat
Finger guards are used to protect
fingers and so bond does not stick to skin and any oils from the skin
will not affect preparation |
Making the Pre-bonded tip with 3 method options
|
 |
DEMO
PICTURES COMING SOON!
|
Hot Pot and fusion chips:
(1) Melt the chips in the Hot Pot
(2)
Cut off 1/4" hair from weft, or take it off of bulk hair if using bulk, or take the strand of a previously bonded hair
If you are color blending you can place the 2 wefts on top of each other and cut them off together and blend.
(3) Dip 1/4" of the top of the hair strand into the Hot Pot and whirl around until the tip is completely saturated with bond
(4) Pull strand over the edge of the pot and lift away and out of the
Hot Pot and make a circular motion around until the bond and the hair
strand separates from the edge of the Hot Pot (like whirling cotton candy)
(5) For Hot Fusion Bonding System: Slightly flatten the tip leaving
extra bond to fuse to natural hair when installing, trim the tip of
excessive bond
(6) For Cold link/loc/ring System: Roll the tip in between fingers making the tip into a shoe lace or i tip shape, trim the tip of excessive bond
|
|
DEMO
PICTURES COMING SOON!
|
|
Fusion Iron and pellets or fusion chips:
(1) Place a pellet or chip on the groove of the heated Fusion Iron tip and allow to melt
(2)
Cut off 1/4" hair from weft, or take it off of bulk hair if using bulk, or take the strand of a previously bonded hair
(3)
Cut off 1/4" hair from weft of take it off of bulk hair if using bulk.
If you are color blending you can place the 2 wefts on top of each other and cut them off together and blend.
(4) Insert about 1/4" of the top of the strand in the Fusion Iron groove and completely saturate the strand with bond
(5) For Hot Fusion Bonding System: Slightly flatten the tip leaving
extra bond to fuse to natural hair when installing, trim the tip of
excessive bond
(6) For Cold link/loc/ring System: Roll the tip in between fingers making the tip into a shoe lace or i tip shape, trim the tip of excessive bond |
|
DEMO
PICTURES COMING SOON!
|
| Glue gun and bonding sticks:
(1) Insert the bonding stick into the glue gun and allow to heat up
(2)
Cut off 1/4" hair from weft, or take it off of bulk hair if using bulk, or take the strand of a previously bonded hair
If you are color blending you can place the 2 wefts on top of each other and cut them off together and blend.
(3) Take 1/4" of the top of the hair strand and place a bead of bond from the tip of the glue gun onto the tip and whirl around on the glue gun tip until the tip is completely saturated with bond
(4) Lift away and off of the Glue Gun and make a circular motion around until the bond and the hair
strand separates from the Glue Gun tip (like whirling cotton candy)
(5) For Hot Fusion Bonding System: Slightly flatten the tip leaving
extra bond to fuse to natural hair when installing, trim the tip of
excessive bond
(6) For Cold link/loc/ring System: Roll the tip in between fingers making the tip into a shoe lace or i tip shape, trim the tip of excessive bond
|
|
Place finished pre-tipped hair into the drawing mat for future use of for preparation for storage.
|
| |
| | |
|
|
|